Bench Grinder Complete With An Add-On Metal Polishing Kit Suitable for polishing aluminium, steel, stainless steel, brass. As this machine has a medium sized 250W motor it is suitable for polishing craft sized items, using light pressure. Supplied with our Short Version of Spindle Adapters as these take up less space on the workbench.
The Main Image above shows the Polishing Kit Assembled to the Bench Grinder (shown on its own in another image) and also shows the Polishing Kit Component Parts Separately in the Same Image. The Bench Grinder and Polishing Add-On Kit are supplied separately.For Assembly Instructions and Kit Contents Please Read Below. Tools required (not supplied) are a 19mm spanner and a Philips Screwdriver. 1 x Draper 250W (1/3hp) 6 Bench Grinder. Supplied fitted with a UK 3 Pin Electrical Plug. International buyers need to fit their own plug / adapter which is suitable for use in their own country. 1 x 150mm Fine Grinding Wheel. 1 x 150mm Medium Grinding Wheel.
The Motor will Run Hot. The run time is around 20 - 25 minutes on, allow to cool, then continue. Do Not Push Hard against the polishing wheels.
This will strain the motor. Using Light Pressure with the correct polishing procedures and this will get satisfactory results. Approximate length Bench grinder with spindle adapters connected - 44 cms. Longer with the flexible drive shaft attached. Further information is shown in the operator's manual supplied in the box with the machine.
Safety - When polishing using the spindle adapters attached to the bench grinder, suitable safety glasses, gloves and dust mask (not supplied) must be worn Scratch Removal - If there are scratches in the item surface then a series of abrasive discs / pads (eg 500 to 2000 Grit) may need to be used first prior to the polishing process. Assembly - The Polishing Kit is supplied separately to the Bench Grinder and needs to be assembled / attached by the following method.Once the bench grinder side guards and the grinding wheels have been removed (please note that the left hand grinder shaft has a left hand nut), the mop spindle adapters are then slid over the grinder shafts. There is a right hand and a left hand spindle adapter in the kit. Please remove the grub screws in the adapters first and then fit the adapters as far as they will go onto the shaft. Once fitted, reinsert the grub screws (one in each adapter) and tighten them using your allen key (not supplied). Polishing Add-On Kit Contents 2 x Bench Grinder Spindle Adapters (1 x left and 1 x right) These are used to attach polishing mops to the bench grinder shafts.
1 x 6" x 1/2" Sisal Metal Polishing Wheel. 1 x 6" x 1/2" White Stitch Metal Polishing Wheel. 1 x 6" x 1/2" Loose Fold Polishing Wheel. For use with the flexible drive shaft. 1 x 75mm Loose Fold Soft Cotton Polishing Mop 1 x 100mm Loose Fold Soft Cotton Polishing Mop.3 x Mounted Cotton Mops (1 each of cylinder, dome, goblet) - 6mm shank. 4 x Felt Bobs (1 each of cylinder, conical, bullet, ball) - 6mm shank. 1 x Silverline Flexible Drive Shaft - 1041 mm long. 6mm keyless chuck 1 x Flexible Drive Shaft Adapter - for attaching the flexible drive shaft to the bench grinder shaft. The adapter attaches the same way to the bench grinder shaft as the spindle adapters do. Polishing Compound Bars Weight Approx. 85mm x 20mm x 27mm. There is a typing error in the brown bar label. Please ignore the words'non-ferrous'.
This bar is suitable for use on all metals. 1 x Cloth (colour may vary) 1 x Instructions. Northern Ireland, Channel Islands, Isle of Man. And certain Scotland Post Codes (including some Aberdeenshire Post Codes) as can be seen listed below. The Free Post and Packaging to the above areas does not apply to this listing as the carriers charge a premium to deliver to those areas.
Northern Ireland - Isle Of Man - Isle Of Wight - Channel Islands - And the following Scotland Post Codes AB31 to AB38 AB40 to AB56 HS IV1 to IV28 IV30 to IV32 IV36 to IV40 IV41 to IV49 IV51, IV55 & IV56 IV52 to IV54 IV63 KA27 and KA28 KW1 to KW14 KW17 to KW17 PA20 PA41 to PA49 PA21 to PA38 PA60 to PA78 PH4 to PH41 PH41 to PH42 PH49 to PH50 ZE. Please make sure there is somebody available to receive and sign for the consignment. The carrier will only attempt to deliver twice and if there is nobody there on both occasions the receiver will then have to collect from their local depot within 5 days. The item "250W 6 Bench Grinder With Add-On Deluxe Metal Polishing Kit & Flexi Drive Shaft" is in sale since Monday, September 7, 2020. This item is in the category "Home, Furniture & DIY\DIY Tools & Workshop Equipment\Power Tools\Buffers & Polishers".The seller is "polishingsupplies" and is located in Hook. This item can be shipped to United Kingdom, United States, Japan, Canada, Ireland, Australia, Germany, France, Greece, Italy, Spain, Antigua and barbuda, Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech republic, Denmark, Estonia, Finland, Hungary, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Poland, Portugal, Romania, Slovakia, Slovenia, Sweden, Bahrain, Brazil, New Zealand, China, Israel, Hong Kong, Norway, Indonesia, Malaysia, Mexico, Singapore, South Korea, Switzerland, Taiwan, Thailand, Bangladesh, Belize, Bermuda, Bolivia, Barbados, Brunei darussalam, Cayman islands, Dominica, Ecuador, Egypt, Guernsey, Gibraltar, Guadeloupe, Grenada, French guiana, Iceland, Jersey, Jordan, Cambodia, Saint kitts and nevis, Saint lucia, Liechtenstein, Sri lanka, Macao, Monaco, Maldives, Montserrat, Martinique, Nicaragua, Oman, Pakistan, Peru, Paraguay, Reunion, Turks and caicos islands, Aruba, Saudi arabia, South africa, United arab emirates, Ukraine, Chile, Bahamas, Colombia, Costa rica, Dominican republic, Guatemala, Honduras, Jamaica, Kuwait, Panama, Philippines, Qatar, El salvador, Trinidad and tobago, Uruguay, Viet nam.